Installation Guide for Cinder Wood Products Shou Sugi Ban
The following is an installation guide and Cinder Wood Products assumes no liability for the outcome of the installation. Our products showcase the authentic beauty of wood, celebrating its natural variations in character, color, and grain.
Handle with care to protect the unique qualities and finish of each piece upon delivery. Charred products require extra attention due to their delicate nature; handle gently with even pressure, avoiding dragging on the charred surface.
As Shou Sugi Ban is a wood product, standard industry guidelines for rain screen and siding installation should be observed.
This installation guide is provided as a reference, and Cinder Wood Products is not responsible for the results of the installation.
ACCLIMATIZATION
Upon delivery, ensure that wood is acclimated to the installation location.
Boards are generally shipped between 8-14% moisture content.
Cypress can characteristically have pockets of higher / lower moisture content within a single board.
Allow boards to acclimate to the environment until moisture equilibrium is reached at the installation site.
CWP recommends at least 3-5 days in a cool, covered dry place for proper acclimatization.
RAIN SCREEN
Siding boards must be installed using a rain screen made of rigid furring to allow for proper ventilation.
Rain screens also decrease material contact leaching, premature finish weathering, and dimensional movement due to temperature extremes.
Plan accordingly for installation of a rain screen between the house wrap and siding when framing out windows, doors, and any other framing elements.
The rain screen must be vented and unobstructed at the top and bottom for sufficient air flow. Mesh or screens may be installed at top and bottom of the rain screen wall.
Recommendation is to use a minimum of ¾" untreated spruce furring to create a continuous air gap.
For horizontal siding installation, furring strips installed vertically create an air gap from top to bottom.
For vertical siding installation, furring strips will also be installed vertically creating the same air gap from top to bottom, but an additional layer of horizontal strips will be needed to fasten the siding to.
Never use pressure-treated lumber as furring as it can cause staining. If pressure-treated strapping is unavoidable, butyl tape must cover any surfaces that the siding comes in contact with the pressure-treated wood.
SIDING INSTALLATION
Siding layout and joints should be planned and laid out in advance, but not kept in the sun for extended periods of time. Boards can be arranged by color graduation with darker boards being installed on the sunnier faces.
Proper industry standard gapping and clearances are required to avoid moisture absorption and seepage especially in exterior installations. Butt joints should not be tight fitting and recommended clearances to other building material types and the ground should be followed. Board shrinkage within the first year after installation is normal and expected.
Boards must be sealed on all cut edges. Any additional on-site cuts must be sealed with the supplied can of touch-up material or recommended sealant.
To remove soot residue after char-on installation, interior walls can be wiped down with a water and a cloth and exterior walls with a water hose but never pressure washed.
Once installed, material can be touched up to seal handling blemishes but differences in the material should be embraced as it is part of the beauty.
FASTENERS
Use required nailing patterns and recommended fasteners to avoid corrosion and staining.
Use stainless steel fasteners. Screws or siding ring-shank face nails may be used.
CWP recommends Simpson Strong-Tie® fasteners.
To order, email info@cinderwoodproducts.com
Must use two (2) fasteners through the face of the board every 16 inches on-center.
Drill pilot holes if within 2" of an end cut.
Drill pilot holes if screws are used.
For Char-on siding installation, do not overdrive fasteners beyond flush.
We recommend hand driving nails with careful attention to avoid hammer mark blemishes as these areas will weather more quickly.
If using a nailer, reduce pressure to start the nail, then finish driving by hand.
If using screws, drill pilot holes and do not overtighten.
As a general rule, fasteners should penetrate at least 1 ¼" into solid wood behind siding.
TRIM, MOLDING, BATTS, AND FLASHING
Cinder Wood Products' shou sugi ban siding comes in the industry standard nominal thickness of ¾". We also offer trim components in a variety of profiles, including timber frame components as large as 18" wide by 18" thick, up to 20' in length. These items are custom orders and may have much longer lead times.
INSTALL IN-LINE WITH RELEVANT STANDARDS
CWP recommended that all installations be in line with the American Architectural Manufacturers Association (AAMA) standards which are relevant to rainscreen wall systems. These standards focus on the performance and weather resistance of rainscreen systems.
AAMA Standards:
AAMA 508
This standard focuses on "Voluntary Test and Classification Method for Pressure Equalized Rain Screen Wall Cladding Systems." It evaluates the ability of a rainscreen system to resist static and dynamic water infiltration while achieving pressure equalization between the interior and exterior of the wall, according to Metal Construction News.
AAMA 509
This standard deals with "Voluntary Test Method for Back-Ventilated and Drained Rain Screen Wall Cladding Systems." It focuses on the ability of the system to allow for proper ventilation and drainage, ensuring the wall assembly remains dry, according to Nichiha.
Architects Institute of America (AIA) Role in Rainscreens:
While the AIA doesn't have a specific standard, it plays a vital role in promoting best practices and standards in the building industry. For example, the AIA Building Performance Knowledge Community Definitions Project has developed definitions for rainscreen walls, emphasizing their role in resisting the five main forces of water penetration: gravity, kinetic movement, surface tension, capillary action, and pressure difference, according to the AIA.
In essence:
AIA doesn't have its own siding or rainscreen standard.
AAMA standards (508 and 509) are key for rainscreen systems.
AIA promotes understanding and application of rainscreen principles in its projects, according to the AIA.
CONTACT US
For more information, or to order fasteners, contact us at info@cinderwoodproducts.com
Cinder
Wood
Products
Hancock, Maine
1-207-460-4630
8a-5p M-F (East Coast Time Zone)
507 Washington Junction Rd
Hancock, ME 04640
Logistics
Species
Accoya®
Cypress
Douglas Fir
Western Hemlock
Eastern White Pine
Sugi (Imported Japanese Cedar - Coming Soon)
Resources
Company
Copyright © 2025 CinderWood Products, All Rights Reserved
